Official Raz Veinz Blogsite

Archive for January, 2015

Honda Air-conditioner Blower Motor Run One Speed Only (Maximum Speed)

Posted in My Automotive Life | No Comments »

In my case, blower motor run  if  I select the maximum speed only from the climate control,  the maximum speed drive by relay (bypass), and the others speed controlled by either transistor (many variable speed)  or coils system (control 4 speed only),  that’s mean, the motor didn’t get the voltage supply from transistor/coils, the main suspect is either transistor/coils or before transistor/coils, my blower motor drive by transistor (mostly modern car use transistor to control the motor speed), enough for the theory, time to troubleshoot!

So, where is the location of transistor? Need to remove the glove box first (very easy task), here the suspect…unplug the socket, then remove two screw (green circle). This is of course you could get the new one, the whole set, but there a pricey…or maybe not available at the local shop, that why the term of DIY is exist.

Remove three screw at the front,

and others two at the back.

The last one inside the case (green circle). To remove thermo fuse, desoldering the blue circle terminal, to remove transistor, desoldering the red circle terminals. Wait! Don’t desoldering it yet, until we know the cause.

This is the main component of  blower motor transistor package, three of them, capacitor, thermo fuse and transistor. First to test is thermo fuse, firstly, detach one of the terminal from circuit (I prefer from the screw side). Check the continuity using multimeter or other method. In my case, there is no continuity, so that mean, this is one of the cause and the more important is, cheap replacement .  The complicated thing is to test the transistor.

To test the transistor, first we need the datasheet, this is the model of original transistor, brand : Toshiba, ID : 2SD1460, type : silicon NPN triple diffused type. And need to know a simple operation of transistor (you can ask uncle google). Make sure to identify the base (B), emitter (E) and collector (C) point.

A simple switching circuit to test an NPN transistor. If the transistor is OK the LED should light when the switch is pressed and not light when the switch is released. Source & details : http://electronicsclub.info/transistors.htm

This is a simple test I make using DC motor as output.

The old vs the new. Used equivalent transistor and thermo fuse.

Put some thermal compound to terminate air gap between transistor and heat sink, for more effective heat transfer.

Put everything back together.

At last, I shoot the trouble…

DIY : Honda Civic/Integra B-Series Thermostat Replacement & IACV/Throttle Body Coolant Bypass

Posted in My Automotive Life | No Comments »

I didn’t have any problem with my thermostat, just do the preventive maintenance, it is something very important that you need to prevent, overheating.  The thermostat is the very important cooling system component,  the main function is to maintain the engine operating temperature, not too cool and not too hot, just simply perfect temperature, like the adjustable hot-cold shower knob, in the cold morning, it will rise the minimum opening temperature quickly (to prevent poor gas mileage, fouled O² sensors, clogged exhaust systems and losing power),  to know how it works, watch the video below.

And this is how cooling system works.

And I have no idea why people cut off the thermostat and bypass the radiator fan (mean the coolant always circulate and the fan will always on) for street car, even for the racing car this modified is only a little bit few.

First, make sure the engine is cold…remove the intake and some wiring to get more access and space.

Prepare some reservoir container under the thermostat housing to make sure the coolant do not spill everywhere (bad for environment and animal), another option is to drain the coolant a little from radiator tank.  Two bolts that need to remove, this one and…

this one.

Take out the thermostat housing, bend the hose to prevent coolant spill, will lose some coolant for sure.

Comparison.

Clean the thermostat housing, then install the new one, don’t worry, there are the mechanism that prevent you from misplace.

I also take this chance to replace the old tired-rubber-hose-that-cannot-withstand-with-the-pressure-anymore with the silicon one, how do I know? Here the picture at the cold temperature.

and here the picture after certain boiling point, scare right? Poom!

Comparison. Silicon vs. stock.

And also the others hose…(please ignore the missing throttle body), and if you look more closer, you will notice that I also do some bypass, the hose that go through throttle body, to cool the intake manifold a little bit. Even wonder why the manufacture design this way? The only reason that I could think is to warm up the throttle body during the winter or very very cold climate to prevent the throttle body butterfly from stuck, but there is not the problem in my country (Malaysia) with benefits from a tropical climate with high temperatures and high humidity throughout the year. And you from the winter sonata country, I didn’t recommend this mod. And for  IACV line, I didn’t really get why…someone? I think for ‘idle’ reason…but, so far, I didn’t have any problem with my idle.

Install everything back in the reverse order of removal. Open the radiator cap and pour coolant into the radiator up to the base of the filler neck, squeeze the radiator hose a little to let the bubbles come out of the top of the radiator.

To remove the bubbles, loosen the bleed bolt (locate under distributor for B-series, but, didn’t  have for type-r series), tighten it again when coolant comes out in a steady stream with no bubbles.

Refill the radiator to the base of the filler neck. Put the cap on the radiator and tighten it only to the first stop (to give a little pressure for fast warm up, or the other method is to rise up the rpm). start the engine and let it run until it warms up (the radiator cooling fan comes on at least twice), that mean, the coolant begins to circulate.

Turn off the engine. Check the level in the radiator, add coolant if needed, install the radiator cap and tighten it fully.

Fill the reservoir to the MAX mark and keep checking the coolant levels.

The perfect cooler your car, the more cooler you are